Graphite Heat Sink Plate For IGBT Power Stacks

Send Inquiry
Graphite Heat Sink Plate For IGBT Power Stacks
Details
Graphite Heat Sink Plate For IGBT Power Stacks An IGBT stack fails at the interface, not in the die. The baseplate spreads heat into a sink, and if the sink and the baseplate expand at different rates the thermal interface degrades cycle by cycle until the junction temperature runs away....
Category
Graphite Block
Share to
Description

Graphite Heat Sink Plate For IGBT Power Stacks

Graphite Heat Sink Plate For IGBT Power Stacks

An IGBT stack fails at the interface, not in the die. The baseplate spreads heat into a sink, and if the sink and the baseplate expand at different rates the thermal interface degrades cycle by cycle until the junction temperature runs away.

Graphite has a thermal expansion close to that of the silicon package and a conductivity high enough to spread heat across the plate, so a graphite sink removes the mismatch that a copper sink introduces on wide temperature swings.

The plate is machined with a flat mounting face and a fin or pin field on the cooling side. Both faces are lapped, because a 0.05 mm flatness error over a 100 mm plate is enough to leave a dry patch under the module.

Key Features

  • Expansion matched to the package - thermal expansion close to the silicon package reduces interface shear

  • Through-plane conductivity - heat spreads laterally instead of forming a hot spot under the die

  • Lapped mounting face - flatness held so the interface material stays continuous

  • Pin or straight fin field - cooling geometry machined to the airflow or cold plate design

  • Electrically non-conductive - no isolation layer needed between the sink and a live baseplate

  • Custom outlines - plate size and hole pattern matched to the stack frame

Technical Specifications

Property Typical Value
Grade high-density fine grain
Density 1.88 - 1.95 g/cm3
Thermal conductivity 130 - 170 W/m.K in plane
Thermal expansion 4.2 - 4.8 x 10-6 per K
Plate thickness 4 - 20 mm
Flatness 0.05 mm on the mounting face
Surface finish Ra 0.8 on the mounting face
Pin diameter 3 - 10 mm
Pin height 5 - 30 mm
Plate size up to 250 mm by 250 mm
Ash content below 0.05 percent
Supply form plate with or without pins

Applications & How to Use

Traction inverter stacks

the plate spreads heat from paralleled IGBT modules

Industrial drive modules

a graphite sink avoids the copper-to-aluminium mismatch

Power cycling test rigs

matched expansion extends interface life under cycling

Rail and vehicle converters

the plate works with cold plate or forced air cooling

Replacement of aluminium sinks

graphite removes the bimetallic interface at the baseplate

Why Choose Jincheng

  • Both faces are lapped and the flatness is reported, so interface contact is predictable
  • Pin geometry is machined to the cooling design rather than to a stock pattern
  • Grade is selected for through-plane conductivity, not just density
  • Expansion values are supplied so the stack designer can check the mismatch
  • Plates are machined in matched pairs for a stack, keeping the modules level
  • Packing protects the lapped face with a removable film

FAQ

Is graphite strong enough for a clamp load

Compressive strength is high, but the plate must be loaded evenly, so a compliant interface pad is normally used

How does it compare with copper

Copper conducts better but expands far more, which is why graphite is chosen where cycling life matters

Can the pins be machined to our layout

Yes, pin diameter, height and pitch are all machined from the cooling design

Do you provide expansion data

Yes, expansion and conductivity values are reported with each batch

Related Graphite Products

Graphite Thermal Bridge Block

Graphite Heat Spreader For SiC Modules

Graphite Grade Selection Checklist

Hot Tags: graphite heat sink plate for igbt power stacks, China graphite heat sink plate for igbt power stacks manufacturers, suppliers, factory, graphite block cylinder, graphite block for conductive heating, graphite block for fuel cell system, machined graphite block, solid block of graphite, solid graphite block

Send Inquiry