Graphite Thermal Bridge Block For Power Module Stacks

Send Inquiry
Graphite Thermal Bridge Block For Power Module Stacks
Details
Graphite Thermal Bridge Block For Power Module Stacks Where a module sits above a cold plate with a gap, heat has to cross that gap through a solid part. A graphite bridge block fills the space with a high-conductivity path and, unlike a metal block, it does not add a large expansion mismatch...
Category
Graphite Block
Share to
Description

Graphite Thermal Bridge Block For Power Module Stacks

Graphite Thermal Bridge Block For Power Module Stacks

Where a module sits above a cold plate with a gap, heat has to cross that gap through a solid part. A graphite bridge block fills the space with a high-conductivity path and, unlike a metal block, it does not add a large expansion mismatch against the cold plate.

The block is machined as a rectangular section with lapped top and bottom faces. Height tolerance is the critical dimension, because an over-thick block loads the module and an under-thick block leaves an air gap that destroys the path.

Where the stack has to be isolated, a thin insulating layer can be bonded to one face, and the block is machined to the finished height including that layer.

Key Features

  • High through-thickness conductivity - heat crosses the gap through a solid graphite path

  • Height held to tolerance - the block does not preload the module or leave an air gap

  • Lapped contact faces - even contact pressure at both interfaces

  • Expansion close to cold plate - lower mismatch than an aluminium or copper block

  • Insulating layer option - a bonded layer provides isolation without a separate sheet

  • Section options - rectangular, stepped or with reliefs for the frame

Technical Specifications

Property Typical Value
Grade high-density fine grain
Density 1.88 - 1.95 g/cm3
Thermal conductivity 130 - 170 W/m.K
Block height 5 - 60 mm
Height tolerance +/-0.05 mm
Face flatness 0.05 mm
Section size up to 150 mm by 150 mm
Compressive strength 95 - 130 MPa
Thermal expansion 4.2 - 4.8 x 10-6 per K
Surface finish Ra 0.8 on contact faces
Isolation layer optional, 100 - 300 micrometre
Supply form single block or matched stack set

Applications & How to Use

Power module stacks

the block bridges the gap between module and cold plate

Traction converters

matched expansion keeps the stack stable under cycling

Test benches

blocks of different heights are used to set interface gap

Isolated stacks

a bonded layer gives isolation without an extra sheet

Replacement of aluminium spacers

graphite removes the bimetallic joint

Why Choose Jincheng

  • Heights are measured individually and marked, so a stack can be assembled without shimming
  • Faces are lapped in the same set-up, keeping the two faces parallel
  • Isolation layers are included in the finished height, not added afterwards
  • Blocks are supplied as matched sets with a height map
  • Conductivity and expansion data are reported per batch
  • Reliefs and steps are machined before the final lapping pass

FAQ

Why is height tolerance so tight

Because the block sits in a clamped stack: too thick preloads the module, too thin leaves an air gap

Can the block be machined to a height map

Yes, a set can be machined to individual heights so the stack is level

Is the isolation layer reliable

It is bonded and then lapped as part of the block, so the interface is controlled rather than assembled in the field

How is flatness verified

Each contact face is checked on a plate and the result is recorded

Related Graphite Products

Graphite Heat Sink Plate For IGBT

Graphite Heat Spreader For SiC Modules

Graphite Grade Selection Checklist

Hot Tags: graphite thermal bridge block for power module stacks, China graphite thermal bridge block for power module stacks manufacturers, suppliers, factory, graphite block for electrolysis system, graphite block for high temperature furnace, graphite block for laboratory equipment, graphite block mold material, small graphite block, solid block of graphite

Send Inquiry