Graphite Filter Plate For Molten Aluminum Filtration - Ceramic Foam Filter Holder

Send Inquiry
Graphite Filter Plate For Molten Aluminum Filtration - Ceramic Foam Filter Holder
Details
Graphite Filter Plate For Molten Aluminum Filtration %MAINIMG% A graphite filter plate holds a ceramic foam filter in the metal stream between the furnace and the casting station. It is the part that seats the filter, seals the edges so metal cannot bypass the filter, and lets the filtered metal...
Category
Graphite Block
Share to
Description

Graphite Filter Plate For Molten Aluminum Filtration

Graphite Filter Plate For Molten Aluminum Filtration

A graphite filter plate holds a ceramic foam filter in the metal stream between the furnace and the casting station. It is the part that seats the filter, seals the edges so metal cannot bypass the filter, and lets the filtered metal flow into the launder without turbulence.

Jincheng machines these plates with a recess sized to the filter grade used, a sealing lip that bears on the filter edge, and flow passages that spread the metal across the whole filter area. Because the plate sits in the metal stream, it is made from dense graphite so it does not absorb aluminium or erode at the sealing lip.

Key Features

  • Filter recess matched to the grade - The recess depth and diameter match the ceramic foam filter size used, so the filter seats flat and metal cannot short-circuit around the edge.

  • Sealing lip on the filter edge - A machined lip bears on the filter border, which forces the whole metal stream through the filter instead of letting it bypass.

  • Dense, non-absorbing graphite - High-density graphite resists aluminium penetration at the lip, which is where a porous grade would fail first.

  • Flow passages spread the stream - Inlet and outlet passages distribute metal across the filter face, so the effective filtration area is used rather than a hot spot in the middle.

  • Replaceable filter, reusable plate - The ceramic filter is replaced every cast or every shift; the graphite plate stays in service until the lip erodes.

  • Matched to the launder - The plate outside dimensions and the joint faces are machined to the existing launder, so it drops into the metal stream without modification.

Technical Specifications

Property Typical Value
Material High-density moulded or isostatic graphite
Bulk density 1.80 to 1.92 g/cm3
Open porosity Below 10 percent
Plate size Up to 400 x 400 mm
Plate thickness 20 to 80 mm
Filter recess diameter 50 to 230 mm
Recess depth 10 to 50 mm
Sealing lip width 5 to 20 mm
Ash content Below 0.1 percent
Surface finish Ra 1.6 to 3.2 um
Service temperature Up to 800 C in air
Typical life 6 to 24 months with filter changes

Applications & How to Use

Aluminium billet and slab casting

The plate sits in the launder ahead of the mold; the filter removes oxide film and inclusions before the metal enters the mold.

Wheel and structural casting

A plate with a matched recess holds a 50 to 100 mm filter in the transfer launder between furnace and machine.

Foundry degassing stations

The plate is mounted after the degasser so filtered metal reaches the casting station without re-oxidation.

Recycled aluminium processing

Coarser filters and a wider recess handle the higher inclusion load of secondary metal.

Filter changeover practice

The ceramic filter is lifted out and replaced; the graphite plate is inspected for lip erosion and re-used.

Why Choose Jincheng

  • The filter recess is machined to the filter grade the customer uses, so the filter seats flat and metal cannot bypass it.
  • Dense graphite resists aluminium penetration at the sealing lip, which is the failure point on cheaper plates.
  • Flow passages are designed to use the whole filter area instead of a central hot spot.
  • Plates are machined to the existing launder dimensions, so no modification is needed at installation.
  • We supply single plates for trials and repeat plates against the original drawing.
  • Plates are shipped with the recess protected so the sealing lip arrives intact.

FAQ

Why does metal bypass the filter?

Usually the recess is too deep, the lip is eroded, or the filter size does not match. A machined recess and a firm sealing lip are what force the metal through the filter.

How often is the graphite plate replaced?

The ceramic filter is changed frequently, but the graphite plate typically lasts 6 to 24 months depending on metal flow and alloy.

Can the plate be used with a 17 inch filter?

Yes, recesses are machined for the common 9, 15, 17 and 20 inch filter sizes, or to the customer's own filter dimension.

Does graphite react with molten aluminium?

Graphite does not wet aluminium at these temperatures, so the plate stays clean. Very long contact at high temperature can form aluminium carbide at the surface.

Do you machine the launder joint faces?

Yes, the outside dimensions and joint faces are machined to the customer's launder drawing so the plate drops in.

Related Graphite Products

Graphite Degassing Rotor And Shaft

Graphite Block And Plate Products

Hot Tags: graphite filter plate for molten aluminum filtration - ceramic foam filter holder, China graphite filter plate for molten aluminum filtration - ceramic foam filter holder manufacturers, suppliers, factory, graphite block blank, graphite block cube, graphite block EDM use, graphite block for laboratory equipment, graphite block for metal processing, graphite carbon block

Send Inquiry